Sioux-tools IW150HAO User Manual download pdf

Form ZCE763 1 Date 2005December16/A

Form ZCE763

Date 2005December16/A

Page 1 of 16

INSTRUCTIONS & PARTS LIST FOR

IW150HAI & IW150HAO SERIES IMPACT WRENCHES

SERIAL “A”

SIOUX IW150 SERIES IMPACT WRENCH

We consider the Sioux IW150 series impact wrench to be an extra heavy duty tool used for steel erection, mining, MRO, heavy duty assembly/disas-

sembly and construction applications. The heart of the IW150 is the rugged and reliable twin hammer clutch, encased in a rugged steel clutch housing.

Following a few simple guidelines will greatly extend the life of your tools.

FIRST AND FOREMOST:

The use of other than genuine Sioux replacement parts may compromise your tools performance, operator safety, and also lead to higher than normal

maintenance and repair requirements.

ADDITIONALLY:

1. All Sioux IW150 impact wrenches are designed to be operated on 90 PSI (6.2 bar) air pressure, with clean dry air, and a minimum 3/4" ID air hose.

Using higher air pressure to increase torque output will drastically shorten tool life.

2. Air tool lubrication is critical to achieving the maximum performance and life from your air tools. We strongly suggest daily lubrication thru the air

inlet, or if using an inline lubricator, install it as close to the tool as possible. One drop of oil per minute is adequate lubrication for most air motors.

3. Proper lubrication of the Impact Clutch mechanism must also be maintained. This unit is equipped with a pressure feed lubrication system and may

be re-greased thru the fitting in the throttle handle. Use caution when using high pressure lubrication equipment to lubricate the clutch as too much

grease can cause a loss of torque output. We recommend the use of a high quality impact grease such as Sioux Catalog No. 289A grease or an

equivalent. (Lubricate once a week during normal use).

4. The way impact tools are used may cause some fasteners to loosen, leading to tool failure. Daily inspect all bolts, screws, and threaded fasteners to

be sure that they are properly tightened.

5. All Sioux air tools should be operated and maintained in accordance with American National Standards Institute Safety Code for Portable Air Tools

(ANSI B 186. 1) and any other applicable safety codes and regulations. ANSI B186.1 information is available from National Standards Institute, Inc.,

11 W 42nd Street, New York, NY 10036.

6. Projectile Hazards: Always wear safety glasses to prevent loss of sight or eye injury from flying projectiles when operating power tools. Do not use

Hand Sockets -use only Impact Sockets in good condition. Hand and/or worn sockets can shatter causing serious injury! Never operate the

tool off of the work. It may run too fast and cause the accessory to be thrown off the tool. Always use the simplest hook-up possible. Long, springy

extension bars and adapters absorb impact power and could break. Use deep Impact Sockets wherever possible in place of extension bars.

AIR SUPPLY

The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter, pressure regulator, and lubrica-

tor will insure maximum output and life of tools. Before connecting tool, blow out the air line to remove water and dirt which may have accumulated.

SOCKETS

Use only impact sockets in good shape.

Use deep socket rather than extension bars.

Ensure that the socket is held square to the fastener and that the tool is in-line with the socket.

If the tool looses power, check the following:

Air Pressure

Ensure that there is an adequate supply of clean, dry air at 90 psi (6.2 bars).

Sockets

Check for loose, worn, or cracked sockets.

Dirt or Debris In Tool or Water In Air Lines

Add petroleum solvent to the inlet of the tool. Run to flush dirt and debris from tool. Repeat if necessary. Lubricate air motor immediately following flush-

ing. Drain water from air lines.

Original

Instructions

250 Snap-on Drive • PO Box 1596 • Murphy, NC 28906 • USA • Phone: 828-835-9765 •www.siouxtools.com

SAVE THESE INSTRUCTIONS!

Read and understand these instructions before operating this tool.

WARNING

When used improperly power tools can create hazardous situations.

Everyone using, maintaining, changing accessories or working near this tool must read, understand and follow these Safety Instructions!

Improperly used power tools can cause injury or death.

1 2 3 4 5 6 ... 15 16

Summary of Contents

Page 1 - SERIAL “A”

Form ZCE763 1 Date 2005December16/AForm ZCE763Date 2005December16/APage 1 of 16INSTRUCTIONS & PARTS LIST FOR IW150HAI & IW150HAO SERIES IMPAC

Page 2 - 2 Date 2005December16/A

Form ZCE763 10 Date 2005December16/ADÉCLARATION DE CONFORMITÉLa société Sioux Tools, Inc., située à : 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 2

Page 3

Form ZCE763 11 Date 2005December16/AINSTRUCTIES EN STUKLIJST VOOR IW150HAI EN IW150HAO SERIE MOERENAANZETTERSSERIE “A”SIOUX IW150 SERIE MOERENAANZETT

Page 4 - 4 Date 2005December16/A

Form ZCE763 12 Date 2005December16/ACONFORMITEITSVERKLARINGOndergetekende, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, US

Page 5 - ADVERTENCIA

Form ZCE763 13 Date 2005December16/ASIOUX SLAGHYLSNYCKLAR MODELL IW150Sioux slaghylsnyckel modell IW150 är ett extra slitstarkt verktyg som används f

Page 6 - 6 Date 2005December16/A

Form ZCE763 14 Date 2005December16/AFÖRSÄKRAN OM ÖVERENSSTÄMMELSEVi, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, för

Page 7 - AVVERTIMENTO

Form ZCE763 15 Date 2005December16/AINSTRUCTIONS & PARTS LIST FOR IW150HAI & IW150HAO SERIES IMPACT WRENCHESSERIAL “A”Fig. Part No. No. Descr

Page 8 - 8 Date 2005December16/A

Form ZCE763 16 Date 2005December16/A250 Snap-on Drive • PO Box 1596 • Murphy, NC 28906 • USA • Phone: 828-835-9765 •www.siouxtools.comWARNINGSome du

Page 9 - AVERTISSEMENT

Form ZCE763 2 Date 2005December16/ADECLARATION OF CONFORMITYWe, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare u

Page 10 - 10 Date 2005December16/A

Form ZCE763 3 Date 2005December16/ABEDIENUNGSANLEITUNG UND TEILELISTE FÜR SCHLAGSCHRAUBER DER SERIE IW150HAI & IW150HAOSERIE “A”SCHLAGSCHRAUBER D

Page 11 - WAARSCHUWING

Form ZCE763 4 Date 2005December16/AKONFORMITÄTSERKLÄRUNGWir, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, erklären hi

Page 12 - 12 Date 2005December16/A

Form ZCE763 5 Date 2005December16/AINSTRUCCIONES Y LISTA DE PIEZAS PARA LLAVES DE IMPACTO NEUMÁTICAS DE LA SERIE IW150HAI Y IW150HAOSERIE “A”LLAVE DE

Page 13 - SERIE “A”

Form ZCE763 6 Date 2005December16/ADECLARACION DE CONFORMIDADNosotros, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, d

Page 14 - 14 Date 2005December16/A

Form ZCE763 7 Date 2005December16/AISTRUZIONI E LISTINO PARTI PER LE CHIAVI PNEUMATICHE SERIE IW150HAI e IW150HAOSERIAL “A”CHIAVE PNEUMATICA SERIE IW

Page 15

Form ZCE763 8 Date 2005December16/ACERTIFICAZIONE DI CONFORMITALa Sioux Tools, Inc, con sede al 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906,

Page 16 - 16 Date 2005December16/A

Form ZCE763 9 Date 2005December16/AINSTRUCTIONS ET LISTE DE PIÈCES DÉTACHÉES POUR CLÉS À CHOCS DES SÉRIES IW150HAI ET IW150HAOSÉRIE " A "C

Related models: IW150HAI

Comments to this Manuals

No comments

Sioux-tools IW150HAO User Manual

Browse online or download User Manual for Power tools Sioux-tools IW150HAO. Sioux Tools IW150HAO User Manual

Summary of Contents

Related models: IW150HAI

Comments to this Manuals

Related products and manuals for Power tools Sioux-tools IW150HAO