Sioux-tools NO. 2S User Manual download pdf

INSTRUCTIONS & PARTS LIST FOR NO. 2S SERIES SCREWDRIVERS & DRILLS

SERIAL “D”

Read and understand "Safety Instructions For Air Tools" and these instructions before

operating this tool.

AIR SUPPLY

The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter, pressure regulator,

and lubricator will insure maximum output and life of tools. Before connecting tool, blow out the air line to remove water and dirt which

may have accumulated.

HOSE AND HOSE CONNECTIONS

Supply hose should be not less than 3/8" (10mm) I.D. Extension hoses should be at least 1/2" (13mm) I.D. Use couplings and fittings

with at least 3/8" (10mm) I.D.

LUBRICATION

Use SIOUX No. 288 air motor oil. An airline lubricator, set to deliver 2 to 4 drops per minute, is recommended. If a lubricator is not used,

add .04 oz. (1.2cc, 12 to 15 drops) of oil into the air inlet twice daily.

Lubricate the gearing every 100 hours of operation with SIOUX No. 289A grease.

Lubricate positive and adjustable clutches every 40 hours with SIOUX No. 1232A grease.

GENERAL OPERATION

Depress the trigger to start the tool. Motor speed may be controlled by adjusting the slotted head screw on the top rear of the tool.

On reversing tools, the direction of spindle rotation is controlled by the reversing lever on the bottom front of the tool.

CLUTCH OPERATION INFORMATION

SCREWDRIVERS AND NUT RUNNERS

STALL DRIVE .......................................... Spindle turns with motor. Motor stalls when fastener is tight.

DIRECT CLUTCH ...................................Spindle doesn’t turn with motor. Pressure on spindle engages straight jaws to turn

spindle. Motor stalls when fastener is tight.

POSITIVE CLUTCH-ANGULAR JAW .....Spindle doesn’t turn with motor. Pressure on spindle engages angular jaws to turn

spindle. Clutch ratchets when certain tightness is reached. Torque on the fastener is

determined by how hard the operator pushes on the tool.

POSITIVE CLUTCH ROLLER JAWS .....Similar to angular jaw except 4 rollers engage angular teeth. Ratchets faster and blow not

as hard. For applications requiring lower torque.

ADJUSTABLE CLUTCH .........................Spindle doesn’t turn with motor. Pressure on spindle engages the clutch, causing the

spindle to turn. When fastener reaches a preset torque, clutch will ratchet. Adjusting

spring pressure will change torque.

ADJUSTMENT OF ADJUSTABLE CLUTCH

ABOVE 25 INCH POUNDS

To adjust clutch place adjusting wrench (No. 53099) with pin

through opening in the clutch case. Place 1/4" (6.4 mm) HEX

wrench in the Bit Holder, press in and turn until adjusting wrench

falls into the slot of the Nut of the Clutch. Keep Bit Holder depressed

in with HEX Wrench and turn clockwise to increase and counter-

clockwise to decrease Torque.

BELOW 25 INCH POUNDS CHANGE TO GREEN

SPRING NO. 41284

Again place adjusting wrench in position as for the higher Torque,

but place a screw driver blade through the bit holder opening until

in contact with the slot at the far end. Rotate screw driver until

adjusting wrench falls into place, again rotate screw driver clock-

wise to increase and counterclockwise to decrease Torque.

Form ZCE630B

Date 2003September25/A

Page 1 of 20

Printed In U.S.A.

ADJUSTING WRENCH

INCREASE

DECREASE

DEPRESS SPINDLE

TO ENGAGE

CLUTCH JAWS

53099

1 2 3 4 5 6 ... 20 21

Summary of Contents

Page 1 - SERIAL “D”

1INSTRUCTIONS & PARTS LIST FOR NO. 2S SERIES SCREWDRIVERS & DRILLSSERIAL “D”Read and understand "Safety Instructions For Air Tools"

Page 2

10MESURES DU SON ET DES VIBRATIONS2S1103, 2S1105, 2S1107 72,28 84,25 Moins de 2,52S1202, 2S1202B, 2S1203, 2S1205, 2S1207 72,28 84,25 Moins de 2,52S130

Page 3

11INSTRUCTIES EN STUKLIJST VOOR SCHROEVEDRAAIERS EN BOREN UIT DE 2S SERIE|SERIENUMMER “D”Voordat u met de machine aan de slag gaat, moet u deze instru

Page 4

122S1100, 2S1110, 2S1130 73,18 84,70 Minder dan 2,52S1200, 2S1210, 2S1230 73,18 84,70 Minder dan 2,52S1300, 2S1310, 2S1330 73,18 84,70 Minder dan 2,52

Page 5

13INSTRUKTIONER OCH RESERVDELSLISTA FÖRNR. 2S SERIES SKRUVMEJSLAR & BORRARSERIE “D”Läs och sätt dig in “Säkerhetsföreskrifter för tryckluftsverkty

Page 6

142S1100, 2S1110, 2S1130 73,18 84,70 Mindre än 2,52S1200, 2S1210, 2S1230 73,18 84,70 Mindre än 2,52S1300, 2S1310, 2S1330 73,18 84,70 Mindre än 2,52S14

Page 7

15MEMO

Page 8

Page 9 - SÉRIE “D”

171. 65009 Screw—M4 x .7 (10)*2. 21491 Ring—Retainer3. 68235 Ass’y—Housing (Drill)68268 Ass’y—Housing (Screwdriver)4. 44383 Shaft—Cluster Gear5. 30235

Page 10 - PN8NTC1 ISO 8662

18FURNISH CATALOG, SERIAL, AND MODEL NUMBER WHENORDERING PARTS30. 2497 Bushing (Magnetic Only)COMPLETE ASSEMBLY63481 Ass’y—Complete Clutch(Screwdriver

Page 11 - SERIENUMMER “D”

19PARTS LIST FOR ADJUSTABLE CLUTCH1. 44520 Retainer—Finder2. 2525 Bit Holder—Magnetic (Magnetic Only)3. 2497 Bushing (Magnetic. Only)6. 54076 Protecto

Page 12

22S1100, 2S1110, 2S1130 73.18 84.70 Less than 2.52S1200, 2S1210, 2S1230 73.18 84.70 Less than 2.52S1300, 2S1310, 2S1330 73.18 84.70 Less than 2.52S140

Page 13 - SERIE “D”

20Printed In U.S.A.Der durch Elektrosanden, -sägen, -schleifen und -bohren sowie durch andere Bauarbeiten anfallendeStaub enthält Chemikalien, die nac

Page 14

This pdf incorporates the following model numbers: 2S2305Q

Page 15

3BEDIENUNGSANLEITUNG UND TEILELISTE FÜRSCHRAUBENDREHER UND BOHRER DER SERIE 2SSERIE “D”Vor dem Betrieb dieses Werkzeugs lesen Sie bitte diese Anweisun

Page 16

42S1100, 2S1110, 2S1130 73,18 84,70 Weniger als 2,52S1200, 2S1210, 2S1230 73,18 84,70 Weniger als 2,52S1300, 2S1310, 2S1330 73,18 84,70 Weniger als 2,

Page 17

5INSTRUCCIONES Y PIEZAS PARA LAS SERIES DE TALADROS Y ATORNILLADORES NO 2SSERIE “D”Lea y entienda las “Instrucciones de seguridad para herramientas ne

Page 18 - TIVE “D” CLUTCHES

62S1103, 2S1105, 2S1107 72,28 84,25 Menos de 2,52S1202, 2S1202B, 2S1203, 2S1205, 2S1207 72,28 84,25 Menos de 2,52S1301, 2S1302, 2S1303, 2S1303A, 2S130

Page 19

7ISTRUZIONI E LISTINO PARTI PER CACCIAVITE E TRAPANI SERIE N. 2SSERIE “D”Leggere attentamente le “Istruzioni per l’uso sicuro di apparecchiature pneu

Page 20 - Printed In U.S.A

82S1100, 2S1110, 2S1130 73,18 84,70 Inferiore a 2,52S1200, 2S1210, 2S1230 73,18 84,70 Inferiore a 2,52S1300, 2S1310, 2S1330 73,18 84,70 Inferiore a 2,

Page 21 - 2S2305Q

9INSTRUCTIONS ET LISTE DES PIECES DETACHEES POURPERCEUSES ET TOURNEVIS DE SERIE 2SSÉRIE “D”Lisez avec attention les “Instructions de mise en garde lor