Sioux-tools SD9APB User Manual download pdf

INSTRUCTIONS FOR SD9APB SERIES SCREWDRIVERS

SERIAL “B”

Read and understand "Safety Instructions For Air Tools" and these instructions before

operating this tool.

AIR SUPPLY

The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter,

pressure regulator, and lubricator will insure maximum output and life of tools. Before connecting tool, blow out the air line

to remove water and dirt which may have accumulated.

HOSE AND HOSE CONNECTIONS

Supply hose should be not less than 3/8" (10mm) I.D. Extension hoses should be at least 1/2" (13mm) I.D. Use couplings

and fittings with at least 3/8" (10mm) I.D.

LUBRICATION

Use SIOUX No. 288 air motor oil. An airline lubricator, set to deliver 2 to 4 drops per minute, is recommended. If a lubricator

is not used, add .04 oz. (1.2cc, 12 to 15 drops) of oil into the air inlet twice daily.

Lubricate the gearing every 100 hours of operation with SIOUX No. 289A grease.

Lubricate positive and adjustable clutches every 40 hours with SIOUX No. 1232A grease.

GENERAL OPERATION

The air motor is started by depressing the operating lever or trigger.

On reversing tools, the direction of spindle rotation is controlled by the reversing button. When the button is

depressed, the spindle rotates counterclockwise. Always depress the button fully to obtain full power. The revers-

ing button on some models can be locked in the reverse direction by fully depressing and rotating the button

clockwise.

Clutch Operation Information

Screw Drivers And Nut Runners

STALL DRIVE ...........................................Spindle turns with motor. Motor stalls when fastener is tight.

DIRECT CLUTCH ......................................Spindle doesn’t turn with motor. Pressure on spindle engages straight jaws to turn

spindle. Motor stalls when fastener is tight.

POSITIVE CLUTCH-ANGULAR JAW ........Spindle doesn’t turn with motor. Pressure on spindle engages angular jaws to turn

spindle. Clutch ratchets when certain tightness is reached. Torque on the fastener is

determined by how hard the operator pushes on the tool.

POSITIVE CLUTCH ROLLER JAWS ........Similar to angular jaw except 4 rollers engage angular teeth. Ratchets faster and blow

not as hard.

ADJUSTABLE CLUTCH ............................Spindle doesn’t turn with motor. Pressure on spindle engages the clutch, causing the

spindle to turn. When fastener reaches a preset torque, clutch will ratchet. Adjusting

spring pressure will change torque.

Adjustment of Adjustable Clutch

ABOVE 25 INCH POUNDS

To adjust clutch place adjusting wrench (No. 53099) with pin

through opening in the clutch case. Place 1/4" (6.4 mm) HEX

wrench in the Bit Holder, press in and turn until adjusting

wrench falls into the slot of the Nut of the Clutch. Keep Bit

Holder depressed in with HEX Wrench and turn clockwise to

increase and counterclockwise to decrease Torque.

BELOW 25 INCH POUNDS CHANGE TO GREEN SPRING NO.

41284

Again place adjusting wrench in position as for the higher

Torque, but place a screw driver blade through the bit holder

opening until in contact with the slot at the far end. Rotate screw

driver until adjusting wrench falls into place, again rotate screw

driver clockwise to increase and counterclockwise to decrease

Torque.

Form ZCE641A

Date 2005April15/B

Page 1 of 22

Printed In U.S.A.

ADJUSTING WRENCH

INCREASE

DECREASE

DEPRESS SPINDLE

TO ENGAGE

CLUTCH JAWS

53099

1 2 3 4 5 6 ... 21 22

Summary of Contents

Page 1 - SERIAL “B”

1INSTRUCTIONS FOR SD9APB SERIES SCREWDRIVERSSERIAL “B”Read and understand "Safety Instructions For Air Tools" and these instructions beforeo

Page 2

10*Pression acoustique *Puissance acoustique *VibrationCatalog No. dBA dBA m/s2SD9APB-4 77,9 89,5 Moins de 2,5SD9APB-7 77,9 89,5 Moins de 2,5SD9APB-12

Page 3 - “B-SERIE”

11PERSLUCHTTOEVOERHet gebruik van droge perslucht met de geschikte druk (90 psig / 6,2 bar) is bepalend voor een goed rendement van demachine. Het mon

Page 4

12Catalogus- *Geluidsdruk *Geluidsvermogen *Trilling nummer dBA dBA m/s2SD9APB-4 77,9 89,5 Minder dan 2,5SD9APB-7 77,9 89,5 Minder dan 2,5SD9APB-12 77

Page 5

13LUFTTILLFÖRSELHur effektivt verktyget fungerar beror på korrekt tillförsel av ren torr luft vid 6,2 bar (90 psig). Använd ett ledningsfilter, entryc

Page 6

14*Ljudtryck *Ljudeffek *VibrationKatalog nr. dBA dBA m/s2SD9APB-4 77,9 89,5 Mindre än 2,5SD9APB-7 77,9 89,5 Mindre än 2,5SD9APB-12 77,9 89,5 Mindre ä

Page 7

15FURNISH CATALOG, SERIAL, AND MODEL NUMBERWHEN ORDERING PARTS*Order Quantity As RequiredFig. PartNo. No. DescriptionPARTS LIST FOR SD9APB SERIES MULT

Page 8

16PARTS LIST FORSD9APB SERIES MOTORSSERIAL “B”Fig. PartNo. No. Description1. 10220 Bearing—Ball2. 13550 End Plate—Front3. 14342 Ring—“O”4. 64108 Cylin

Page 9 - CLASSE “B”

171. 21501 Ring—Retaining2. 44660 Ring—Guide3. 21406 Spring—Stall Drive4. 44161 Retainer—Ball5. 10902 Ball—Steel6. 25439 Washer7. 67927 Case—Gear (Sta

Page 10

1813. 67860 Gear—Pinion (1200 RPM)14. 67868 Ass’y—Gear & Bearing (2)* (400, 700 RPM)67865 Ass’y—Gear & Bearing (2)* (1200 RPM)15. 67936 Bushin

Page 11 - SERIE “B”

19COMPLETE ASSEMBLY63482 Ass’y—Complete Clutch(Quick Change)(Figs. 1-4, 10, 11-16)63486 Ass’y—Complete Clutch(Quick Change)(Figs. 3-8, 10, 11-16)63490

Page 12

2*Sound Pressure *Sound Power *VibrationCatalog No. dBA dBA m/s2SD9APB-4 77.9 89.5 Less than 2.5SD9APB-7 77.9 89.5 Less than 2.5SD9APB-12 77.9 89.5 Le

Page 13

2019. 54073 Washer—Index20. 53095 Nut—Adjusting21. 21774 Ring—Retaining22. 53099 Wrench—Adjusting23. 30208 Wrench—Allen24. 21501 Ring—Retaining25. 446

Page 14

21NOTES

Page 15 - AIR SCREWDRIVERS

22Printed In U.S.A.Der durch Elektrosanden, -sägen, -schleifen und -bohren sowie durch andere Bauarbeiten anfallendeStaub enthält Chemikalien, die nac

Page 16 - SERIES MOTORS

3ANWEISUNGEN FÜR SD9APB SERIE SCHRAUBENDREHER“B-SERIE”Vor dem Betrieb dieses Werkzeugs lesen Sie bitte diese Anweisungen und die“Sicherheitsanweisunge

Page 17

4Katalog *Schalldruck *Schallstärke *VibrationNr. dBA dBA m/s2SD9APB-4 77,9 89,5 Weniger als 2,5SD9APB-7 77,9 89,5 Weniger als 2,5SD9APB-12 77,9 89,5

Page 18

5SUMINISTRO DE AIRELa eficiencia de la herramienta depende de un suministro adecuado de aire seco 90 psig (6,2 bar). El uso de un filtro delínea, regu

Page 19

6No de *Presión de sonido *Potencia de sonido *VibraciónCatalogo dBA dBA m/s2SD9APB-4 77,9 89,5 Menos de 2,5SD9APB-7 77,9 89,5 Menos de 2,5SD9APB-12 7

Page 20

7ALIMENTAZIONE ARIAL’efficienza dell’apparecchio dipende da un’adeguata alimentazione di aria pulita ad una pressione di 90 psi (6,2 bar). Per il mas

Page 21

8*Pressioine sonora *Potenza sonora *VibratzioniCatalogo n. dBA dBA m/s2SD9APB-4 77,9 89,5 Inferiore a 2,5SD9APB-7 77,9 89,5 Inferiore a 2,5SD9APB-12

Page 22 - Printed In U.S.A

9ALIMENTATION EN AIRL’efficacité de l’outil dépend de la qualité de l’air d’alimentation, qui doit être sec et propre, et de la pression, qui doit êtr