Sioux-tools VG30AL User Manual download pdf

Form ZCE761 1 Date 2013July18/B

AIR SUPPLY

The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter, pressure regulator, and lubrica-

tor will insure maximum output and life of tools. Before connecting tool, blow out the air line to remove water and dirt that may have accumulated.

HOSE AND HOSE CONNECTIONS

Supply hose should be not less 1/2" (13mm) I.D. Extension hoses should be at least 1/2" (13mm) I.D. Use couplings and fittings with at least 1/2"

(13mm) I.D.

LUBRICATION

•Use SIOUX No. 288 air motor oil. An airline lubricator, set to deliver 3 to 4 drops per minute, is recommended. If a lubricator is not used, fill the oil

reservoir in the handle periodically.

GENERAL OPERATION

• CHECK THE TOOL DAILY WITH A TACHOMETER!

• Mounting Wheels

Cup grinding wheels and 7” & 9” depressed center grinding wheels must be tightened to 120 in-lb. (1.4KG-M) to keep wheels from spinning off.

• Governors

This tool is equipped with a speed control governor.

SIOUX VG30AL SERIES GRINDERS

We consider the Sioux VG30AL series of grinders to be extra heavy duty machines that are used in Foundries, Welding, and Fabrication Shops,

Shipyards, Construction, and a variety of other industries. These tools were designed to handle the tough jobs like grinding, blending, and smoothing.

Following a few simple guidelines will greatly extend the life of your tools and provide the information necessary for the safe use of Grinders.

FIRST AND FOREMOST:

The use of other than genuine Sioux replacement parts may compromise your tool’s performance, operator safety, and also lead to higher than normal

maintenance and repair requirements.

ADDITIONALLY:

1. All Sioux grinders are designed to operate on 90 PSI (6.2 bar) air pressure, with a clean, dry air supply and a minimum 1/2" ID air hose. Using air

pressure higher than 90 PSI to increase speed or power output will drastically shorten tool life and may lead to serious injuries caused by grinding

wheel accidents.

2. Air tool lubrication is critical to achieving the maximum performance and life from your air tools. We strongly suggest daily lubrication through the air

inlet or by using the built-in lubricator in the tool throttle handle. Daily, or at the start of each shift, disconnect the air supply, remove the oil chamber

cap and fill the reservoir with Sioux 288 air motor oil, and replace the chamber cap securely.

3. The way grinders are used may cause some fasteners to loosen, leading to tool failures or injury. Daily inspect all bolts, nuts, and cap screws to be

sure that they are properly tightened, paying particular attention to the wheel guard and its mounting bolts. Never operate this tool without the guard

properly installed!

4. All Sioux air tools should be operated and maintained in accordance with American National Safety Standards Safety Code for Portable Tools (ANSI

B186.1) and any other applicable safety codes and regulations. B186.1 information is available from National Standards Institute Inc., 11 W 42nd

St., New York, NY 10032.

5. WARNING: Hearing loss can result from prolonged exposure to excessive sound levels. Always use approved hearing protection when using power

tools.

6. WARNING: Projectile Hazards - Always wear safety glasses to prevent loss of sight or eye injury from flying projectiles when operating power tools.

The most important safety device for this or any power tool is Y O U. NEVER use grinding wheels, sanding discs, wire brushes, or any other abrasive

accessories that are not rated for the speed of the tool you are using. Serious injury can result.

7. WARNING: Power tools can vibrate in use. Repetitive work motions, uncomfortable positions, and vibrations can cause injury to hands, fingers, or

wrists, of some people. STOP using any tool if discomfort, a tingling feeling, or pain occurs. Seek your supervisor’s advice before resuming use.

ALWAYS wear good quality work gloves to help as insulation against tool vibration and cold.

8. WARNING: Always turn off the air supply and disconnect the air supply hose before installing or removing any accessory on this tool or before per-

forming any maintenance on this tool. Failure to do so could result in injury.

Form ZCE761

Date 2013July18/B

Page 1 of 16

INSTRUCTIONS & PARTS LIST FOR

VG30AL SERIES VERTICAL GRINDERS

SERIAL “A”

Original

Instructions

SAVE THESE INSTRUCTIONS!

Read and understand these instructions before operating this tool.

WARNING

When used improperly power tools can create hazardous situations.

Everyone using, maintaining, changing accessories or working near this tool must read, understand and follow these Safety Instructions!

Improperly used power tools can cause injury or death.

250 Snap-on Drive • PO Box 1596 • Murphy, NC 28906 • USA • Phone: 828-835-9765 •www.siouxtools.com

1 2 3 4 5 6 ... 15 16

Summary of Contents

Page 1 - SERIAL “A”

Form ZCE761 1 Date 2013July18/BAIR SUPPLYThe efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use

Page 2 - 2 Date 2013July18/B

Form ZCE761 10 Date 2013July18/BNIVEAUX ACOUSTIQUES ET VIBRATOIRESRéf. catalogue *Pression acoustique dBA *Puissance acoustique dBA *Vibration m/s2VG

Page 3

Form ZCE761 11 Date 2013July18/BINSTRUCTIES EN STUKLIJST VOOR VG30AL SERIE VERTICALE SLIJPMACHINESSERIE “A”LUCHTTOEVOERDe efficiëntie van het werktui

Page 4 - 4 Date 2013July18/B

Form ZCE761 12 Date 2013July18/BGELUIDS- EN TRILLINGSNIVEAUSCatalogus nummer *Geluidsdruk dBA *Geluidsvermogen dBA *Trilling m/s2VG30AL-60D7 — 88 3

Page 5 - ADVERTENCIA

Form ZCE761 13 Date 2013July18/BANVISNINGAR OCH RESERVDELSLISTA FÖR LODRÄTA SLIPMASKINER MODELL VG30ALSERIE “A”LUFTTILLFÖRSELVerktygets effektivitet

Page 6 - 6 Date 2013July18/B

Form ZCE761 14 Date 2013July18/BLJUD- OCH VIBRATIONSAVLÄSNINGARKatalog nr. *Ljudtryck dBA *Ljudeffektr dBA *Vibration m/s2VG30AL-60D7 — 88 3,6VG30A

Page 7 - AVVERTIMENTO

Form ZCE761 15 Date 2013July18/B51313233343536373839404142434445464748501234567891011121314151617181920212223242526272829303449INSTRUCTIONS & PAR

Page 8 - 8 Date 2013July18/B

Form ZCE761 16 Date 2013July18/B250 Snap-on Drive • PO Box 1596 • Murphy, NC 28906 • USA • Phone: 828-835-9765 •www.siouxtools.comWARNINGSome dust c

Page 9 - AVERTISSEMENT

Form ZCE761 2 Date 2013July18/BDECLARATION OF CONFORMITYWe, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under

Page 10 - 10 Date 2013July18/B

Form ZCE761 3 Date 2013July18/BBEDIENUNGSANLEITUNG UND TEILELISTE FÜR VERTIKAL-SCHLEIFER DER SERIE VG30ALSERIE “A”DRUCKLUFTVERSORGUNGDie Effizienz de

Page 11 - WAARSCHUWING

Form ZCE761 4 Date 2013July18/BSCHALL-UND VIBRATIONSWERTEKatalog-Nr. *Schalldruck dBA *Schallstärke dBA *Vibration m/s2VG30AL-60D7 — 88 3,6VG30AL-4

Page 12 - 12 Date 2013July18/B

Form ZCE761 5 Date 2013July18/BINSTRUCCIONES Y LISTA DE PIEZAS PARA VG30AL RECTIFICADORAS VERTICALES DE LA SERIE VG30AL SERIE “A”SUMINISTRO DE AIREL

Page 13 - SERIE “A”

Form ZCE761 6 Date 2013July18/BLECTURAS DE VIBRABACIONES Y SONIDOSNo de Catálogo *Presión de sonido dBA *Potencia de sonido dBA *Vibration m/s2VG30A

Page 14 - 14 Date 2013July18/B

Form ZCE761 7 Date 2013July18/BISTRUZIONI E LISTINO PARTI PER LE MOLATRICI VERTICALI SERIE VG30ALSERIAL “A”ARIAL’efficienza di quest’utensile dipende

Page 15

Form ZCE761 8 Date 2013July18/BVALORI DI RUMOROSITÀ E VIBRAZIONICatalogo n. *Pressione sonora dBA *Potenza sonora dBA *Vibrazioni m/s2VG30AL-60D7 —

Page 16 - 16 Date 2013July18/B

Form ZCE761 9 Date 2013July18/BINSTRUCTIONS ET LISTE DE PIÈCES DÉTACHÉES POUR MEULEUSES VERTICALES DE SÉRIE VG30ALSERIAL “A”ALIMENTATION D'AIR

Comments to this Manuals

No comments

Sioux-tools VG30AL User Manual

Browse online or download User Manual for Power tools Sioux-tools VG30AL. Sioux Tools VG30AL User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Power tools Sioux-tools VG30AL